HSN code 7219 — FLAT-ROLLED PRODUCTS OF STAINLESS STEEL, OF A WIDTH OF 600 M
HSN · heading18%हिंदी में देखें · தமிழில் பார்க்க
FLAT-ROLLED PRODUCTS OF STAINLESS STEEL, OF A WIDTH OF 600 MM OR MORE
Flat-rolled stainless steel sheets and coils that are at least 600 mm wide. These are semi-finished or finished steel products used in industrial manufacturing, appliances, and construction.
current gst rate
| igst | cgst | sgst | condition |
|---|---|---|---|
| 18% | 9% | 9% | Sch II S.No 272 |
source: 9/2025-Central Tax (Rate) · effective 2025-09-22 · all codes at 18%
gst calculator — pre-filled with this rate
products commonly classified here
cold-rolled stainlessflat stainless steelhot-rolled stainlessSS coilSS sheetsstainless steel coilsstainless steel platestainless steel sheets
more specific codes
- 721911OF A THICKNESS EXCEEDING 10 MM :
- 721912OF A THICKNESS OF 4.75 MM OR MORE BUT NOT EXCEEDING 10 MM
- 721913OF A THICKNESS OF 3 MM OR MORE BUT LESS THAN 4.75 MM
- 721914OF A THICKNESS OF LESS THAN 3 MM
- 721921OF A THICKNESS EXCEEDING 10 MM :
- 721922OF A THICKNESS OF 4.75 MM OR MORE BUT NOT EXCEEDING 10 MM :
- 721923OF A THICKNESS OF 3 MM OR MORE BUT LESS THAN 4.75 MM :
- 721924OF A THICKNESS OF LESS THAN 3 MM :
- 721931OF A THICKNESS OF 4.75 MM OR MORE :
- 721932OF A THICKNESS OF 3 MM OR MORE BUT LESS THAN 4.75 MM :
- 721933OF A THICKNESS EXCEEDING 1 MM BUT LESS THAN 3 MM :
- 721934OF A THICKNESS OF 0.5 MM OR MORE BUT NOT EXCEEDING 1 MM :
- 721935OF A THICKNESS OF LESS THAN 0.5 MM :
- 721990OTHER :
sibling codes
- 7201PIG IRON AND SPIEGELEISEN IN PIGS, BLOCKS OR OTHER PRIMARY FORMS
- 7202FERRO-ALLOYS
- 7203FERROUS PRODUCTS OBTAINED BY DIRECT REDUCTION OF IRON ORE AND OTHER SPONGY FERROUS PRODUCTS, IN
- 7204FERROUS WASTE AND SCRAP; REMELTING SCRAP INGOTS OF IRON OR STEEL
- 7205GRANULES AND POWDERS, OF PIG IRON, SPIEGELEISEN, IRON OR STEEL
- 7206IRON AND NON-ALLOY STEEL IN INGOTS OR OTHER PRIMARY FORMS (EXCLUDING IRON OF HEADING 7203)
- 7207SEMI-FINISHED PRODUCTS OF IRON OR NON-ALLOY STEEL
- 7208FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, HOT-ROLLED, NOT
- 7209FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, COLD- ROLLED (CO
- 7210FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF 600 MM OR MORE, CLAD, PLATED OR
- 7211FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF LESS THAN 600 MM, NOT CLAD, PLAT
- 7212FLAT-ROLLED PRODUCTS OF IRON OR NON-ALLOY STEEL, OF A WIDTH OF LESS THAN 600 MM, CLAD, PLATED O
Not sure this is the right code? Try the guided finder →
compiled from official sources · not tax advice · verify with your tax advisor before filing